Passive control of the flow around a square cylinder using porous media

The passive control of bluff body flows using porous media is investigated by means of the penalization method. This method is used to create intermediate porous media between solid obstacles and the fluid in order to modify the boundary layer behaviour. The study covers a wide range of two‐dimensional flows from low transitional flow to fully established turbulence by direct numerical simulation of incompressible Navier–Stokes equations. A parametric study is performed to illustrate the effect of the porous layer permeability and thickness on the passive control. The numerical results reveal the ability of porous media to both regularize the flow and to reduce the drag forces up to 30%. Copyright © 2004 John Wiley & Sons, Ltd.     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

X-ray damage characterization in BaLiF3,KMgF3 and LiCaAlF6 complex fluorides

Two-inch sized KMgF₃,BaLiF₃ and LiCaAlF₆ (LiCAF) single crystals were grown by the Czochralski method under a CF₄ atmosphere. X-ray irradiation was used to carry out a comparative study of induced optical absorption phenomena and colour centre creation in the ultra-violet and visible spectral regions. The integral of the induced absorption spectra is significantly lower in LiCAF with respect to the other studied materials. It is found that the amplitude of the F-absorption band is suppressed more than a factor of 3 by Mg-doping. For Mg-doped crystals, the optimum doping concentration is about 0.2 mol% of Mg²⁺.     

Dispersion Characteristics of Waveguide Arrays in Optical Spectrum Analyzers

Formulas for calculating the spectral characteristics of waveguide arrays, which are incorporated into waveguide spectrum analyzers based on planar waveguides, channel waveguides, and fiber optical waveguides, are derived taking into account the contribution of both the waveguide dispersion and the material dispersion to the dispersion factor. These formulas are used to study the dependence of the dispersion factor on the waveguide-system parameters for specific models of waveguide arrays. It is shown that consideration of contributions of the waveguide dispersion and material dispersion can affect profoundly the spectral characteristics of waveguide arrays.     

Measurement uncertainty of selenium determination in the reference material Seronorm Trace Elements Serum by hydride generation atomic fluorescence spectrometry

 An analytical result is not considered to be complete without a statement of the measurement uncertainty associated with it. Evaluation of measurement uncertainty is therefore an essential part of every determination. In the present study the measurement uncertainty of the result of determination of selenium in the reference material Seronorm Trace Elements Serum was studied. The combination of a digestion procedure using sulfuric acid, V₂O₅ in H₂SO₄ and hydrogen peroxide and the continuous flow approach of hydride generation atomic fluorescence spectrometry (HG-AFS) detection was used for selenium determination. The total uncertainty budget was calculated with the help of the GUM Workbench program, in which computations follow the rules of the ’ISO guide to the expression of uncertainty in measurement’. The major sources of uncertainty were found to be due to the recovery of the procedure, measurement of peak heights and the purity of Na₂SeO₃. A selenium mass fraction of 77.1±4.8 ng/g (with a coverage factor of 2.1, 95% probability) was determined, which is comparable with the recommended value of 80 ng/g. Received: 13 September 2002 Accepted: 23 December 2002 Acknowledgements We would like to thank Tinkara Buˇcar, B.Sc. for useful discussions and the IAEA Vienna, for financial support of the project 11553/RO. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to V. Stibilj     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.     

Synthesis and optical properties of tetraphenylmethane-based tetrahedral fluorescent compounds and their water-soluble PEG-linked polymers

The synthesis and optical properties of tetrahedral fluorescent compounds comprising of tetraphenylmethane as the core and oligothiophenes as the chromophoric arms, and their water-soluble poly(ethylene glycol)-linked polymers are reported.     

The modified characteristic finite difference fractional steps method for the coupled system of fluid dynamics in porous media and its analysis

For the coupled system of multilayer fluid dynamics in porous media, the modified characteristic finite difference fractional steps method applicable to parallel arithmetic is put forward and two‐dimensional and three‐dimensional schemes are used to form a complete set. Some techniques, such as calculus of variations, energy method, piecewise biquadratic interpolation, multiplicative commutation rule of difference operators, decomposition of high order difference operators and prior estimates are adopted. Optimal order estimates in L² norm are derived to determine the error in the approximate solution. This method has already been applied to the numerical simulation of multilayer fluid dynamics in porous media. © 2003 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 19: 665–681, 2003.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Pulsed-Field-Gradient Measurements of Time-Dependent Gas Diffusion

Pulsed-field-gradient NMR techniques are demonstrated for measurements of time-dependent gas diffusion. The standard PGSE technique and variants, applied to a free gas mixture of thermally polarized xenon and O₂, are found to provide a reproducible measure of the xenon diffusion coefficient (5.71 × 10⁻⁶m²s⁻¹for 1 atm of pure xenon), in excellent agreement with previous, non-NMR measurements. The utility of pulsed-field-gradient NMR techniques is demonstrated by the first measurement of time-dependent (i.e., restricted) gas diffusion inside a porous medium (a random pack of glass beads), with results that agree well with theory. Two modified NMR pulse sequences derived from the PGSE technique (named the Pulsed Gradient Echo, or PGE, and the Pulsed Gradient Multiple Spin Echo, or PGMSE) are also applied to measurements of time dependent diffusion of laser polarized xenon gas, with results in good agreement with previous measurements on thermally polarized gas. The PGMSE technique is found to be superior to the PGE method, and to standard PGSE techniques and variants, for efficiently measuring laser polarized noble gas diffusion over a wide range of diffusion times.